Leading 10 common forklift accidents ， forklift procedure should pay attention to these issues ！.

Don't undervalue the forklift at work. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not use a seat belt and dropped from the car when it rolled over and was crushed.
Forklift operation need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the lots is stable and trusted.
4. The begin has to be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or cars nearby, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the car to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is restricted to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to follow the website traffic rules in the manufacturing facility and have to keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons needs to be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately tilted back. The tons shall not be elevated other than when piling or filling. .
8. The elevation of the tons need to not obstruct the motorist's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and unloading.
1. When fork-loading things, the distance in between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make Stand-on Electric Pallet Stacker use of a fork top or pull. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading products, the forklift must be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch Electric Forklift Truck for Warehouse various other goods or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not glide backwards. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is prohibited to fork items at broadband and hit tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look should be checked, and fuel, lubricating oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Examine whether the lights and horn signals are full and reliable.
4. Throughout the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to get the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844